Selected:

Waveshare ATMEL AVR Programmer USB AVRISP XPII Compatible Atmel at AVR ISP mk2 mkII in-System Programmer Supports AVR Studio 4/5/6/7 Or Higher Version

$39.99

Waveshare ATMEL AVR Programmer USB AVRISP XPII Compatible Atmel at AVR ISP mk2 mkII in-System Programmer Supports AVR Studio 4/5/6/7 Or Higher Version

$39.99

AT AVRISP mkII compliant
– Compatible with AT AVR ISP, easy to use, stable and reliable
Based on AT AVRISP mkII firmware
– Identified as AVRISP mkII in AVRStudio, high speed programming
Upgradable firmware
– Firmware is upgradable to Support Future Devices
– Automatic Upgrade
Supported software
– AVR Studio 4/5/6 or WINAVR(GCC) is used as front-end software
– Supports the program files generated by IAR, ICCAVR, CVAVR
Device Support
– USB AVRISP XPII supports all AVR devices with ISP and PDI Interface. Support for new
devices will be added with new versions of AVR Studio.
– Supports AT86RF401/AT89S51/AT89S52
Refer to AVR Studio 6, the following devices are supported:
Supports all the different voltages and speed grade versions of the devices listed in the table above.
Check more supported devices : UC3, Mega, SAM , Tiny, Xmega
Performance
– High speed programs FLASH , EEPROM, Fuses, and Lock Bit – It takes only 2.5S to program a 12K program file with verification (programming speed was set to 1M while the Max speed could be up to 8M)
Connects to PC
– Uses a USB interface for communication with the front-end software (Probably AVR Studio)
– Using PDIUSBD12, USB 1.1 (USB 2.0 Full Speed) 12Mbits/second – Each USB AVRISP XPII has a unique ID, a PC could connects to several Devices at the same time
Connects to target board
The USB AVRISP XPII connects to the target board through 3 optional cables. Depending on the existed connector on the target board, the cable has to be changed accordingly. – Standard 6-pin ISP Connector, Using 6-pin ISP cable
– Standard 10-pin ISP Connector, Using 6-pin to 10-pin ISP cable
– Custom ISP Connector, Using 6-wire multicolour custom connector cable
The figure 1 and 2 shows the pinouts for the 10-pin and 6-pin ISP connectors.

Supports AVR Studio 4/5/6 Or Higher Version (Delivered With Firmware For AVR Studio 5, Can Be Updated To Support Other AVR Studio Versions)
Supports all AVR devices with ISP or PDI interface, and certain 51 Devices Programs both Flash and EEPROM
Supports Fuses and Lock Bit Programming Based on AT AVRISP mkII firmware
Upgradable to Support Future Devices Adjustable ISP programming speed up to 8M frequency
USB 2.0 compliant (full speed, 12Mbps) 3 optional cables to target board Powered from USB bus, does not require external power supply

Description

Price: $39.99
(as of Dec 04,2021 01:45:40 UTC – Details)



AT AVRISP mkII compliant
– Compatible with AT AVR ISP, easy to use, stable and reliable
Based on AT AVRISP mkII firmware
– Identified as AVRISP mkII in AVRStudio, high speed programming
Upgradable firmware
– Firmware is upgradable to Support Future Devices
– Automatic Upgrade
Supported software
– AVR Studio 4/5/6 or WINAVR(GCC) is used as front-end software
– Supports the program files generated by IAR, ICCAVR, CVAVR
Device Support
– USB AVRISP XPII supports all AVR devices with ISP and PDI Interface. Support for new
devices will be added with new versions of AVR Studio.
– Supports AT86RF401/AT89S51/AT89S52
Refer to AVR Studio 6, the following devices are supported:
Supports all the different voltages and speed grade versions of the devices listed in the table above.
Check more supported devices : UC3, Mega, SAM , Tiny, Xmega
Performance
– High speed programs FLASH , EEPROM, Fuses, and Lock Bit – It takes only 2.5S to program a 12K program file with verification (programming speed was set to 1M while the Max speed could be up to 8M)
Connects to PC
– Uses a USB interface for communication with the front-end software (Probably AVR Studio)
– Using PDIUSBD12, USB 1.1 (USB 2.0 Full Speed) 12Mbits/second – Each USB AVRISP XPII has a unique ID, a PC could connects to several Devices at the same time
Connects to target board
The USB AVRISP XPII connects to the target board through 3 optional cables. Depending on the existed connector on the target board, the cable has to be changed accordingly. – Standard 6-pin ISP Connector, Using 6-pin ISP cable
– Standard 10-pin ISP Connector, Using 6-pin to 10-pin ISP cable
– Custom ISP Connector, Using 6-wire multicolour custom connector cable
The figure 1 and 2 shows the pinouts for the 10-pin and 6-pin ISP connectors.

Supports AVR Studio 4/5/6 Or Higher Version (Delivered With Firmware For AVR Studio 5, Can Be Updated To Support Other AVR Studio Versions)
Supports all AVR devices with ISP or PDI interface, and certain 51 Devices Programs both Flash and EEPROM
Supports Fuses and Lock Bit Programming Based on AT AVRISP mkII firmware
Upgradable to Support Future Devices Adjustable ISP programming speed up to 8M frequency
USB 2.0 compliant (full speed, 12Mbps) 3 optional cables to target board Powered from USB bus, does not require external power supply

Reviews

There are no reviews yet.

Be the first to review “Waveshare ATMEL AVR Programmer USB AVRISP XPII Compatible Atmel at AVR ISP mk2 mkII in-System Programmer Supports AVR Studio 4/5/6/7 Or Higher Version”

Your email address will not be published. Required fields are marked *

Quick Navigation
×
×

Cart